| |
|
|
NOVAK® FIXED LOMOUNT CARRY REAR
FOR
COLT
Gov., Comm., Off.,
SPRINGFIELD,
& SIG GSR
- Mill to bottom of original dovetail, but no
further forward than front of dovetail.
- Cut new dovetail .770" forward of rear edge
of slide. Depth of dovetail is same as depth of
dovetail of sight.
- Deburr sight and slide - Fit sight to slide.
|
 |
|
|
|
|
|
Return to TOP |
|
| |
|
|
NOVAK® EXTREME
DUTY ADJUSTABLE LOMOUNT CARRY REAR
FOR
COLT
Gov., Comm., Off.,
SPRINGFIELD,
& SIG GSR
- Mill to bottom of original dovetail, but no
further forward than front of dovetail.
- Cut new dovetail .770" forward of rear edge
of slide. Depth of dovetail is same as depth of
dovetail of sight.
- To make notch cut for hinge on Adjustable
sight after contacting dovetail at same height
as rear flat go forward .150", check sight fit
and remove metal as needed for proper fit of
sight. This will also retro fit adjustable to
fixed sight dovetail.
- Deburr sight and slide - fit sight to slide.
DIRECTION
When you
find the correct elevation, tighten the set screw
located on the left side of the sight. If you need
to change elevation, remember to release the set
screw before adjusting the elevation screw. Windage
adjustment is accomplished by loosening the main set
screw and drifting the entire sight, tighten main
set screw when desired position is achieved. |
 |
|
|
|
Return to TOP
|
|
|
NOVAK® DOVETAIL
MOUNT FRONT SIGHT
FOR
COLT,
SPRINGFIELD,
SIG GSR,
&
BHP MKII
- Remove existing front sight.
- Mill a small flat approx. .150" wide that
extends .610" back front the front of the slide.
- Measure the total height of the sight blank
(including dovetail), subtract front this the
height of the blade only. The difference is the
depth of the dovetail cut you must make. OR:
Using a depth micrometer, measure from the
bottom of the dovetail to the bottom of the
sight blade.
- With the center of a .330" x 65 degree
dovetail cutter .320" back from the front of the
slide, touch the top of your flat cut, then pick
up the table the predetermined distance
(dovetail depth), and make one pass with the
cutter.
- Deburr the sight and slide before fitting.
- Once the sight blank is installed and
centered on the slide, drill a 1/16th inch hole
through the sight and slide, using the hole in
the sight as a guide. Once the sight is finished
and reinstalled place the 1/16 x 1/4 inch roll
pin through the sight and slide.
|
 |
|
|
|
Return to TOP
|
|
|
NOVAK® BROWNING HI POWER
MKII
- Mill to bottom of original dovetail, but no
further forward than front of dovetail.
- Cut new dovetail .660" forward of rear edge
of slide. Depth of dovetail is the same as
dovetail depth of sight.
- Trim firing pin stop to proper height.
- Deburr sight and slide. Fit sight to slide.
|
 |
|
|
|
Return to TOP
|
|
|
NOVAK® BROWNING HI POWER MKIII
(EARLER)
- Behind existing dovetail, mill a flat to
same dovetail depth as sight, .066±
measure each sight.
- Deburr sight and slide, fit sight to slide.
- Trim firing pin stop.
|
 |
|
|
|
Return to TOP
|
|
|
NOVAK®
BROWNING HI POSER MKIII
(NEWER)
- Measure forward .780" from firing pin stop
and mark slide.
- Measure dovetail on sight, cut flat on slide
till dovetail depth on slide matches dovetail on
sight approx. .074 and up to .780" forward measurement.
- Test fit sight in dovetail and check front
fit.
- It may need more cut out as the rear
dovetail can be a little forward or back on the
slide.
|
|
|
|
|
Return to TOP
|
|
|
NOVAK®
COLT .380
- Mill to bottom of original dovetail, but no
further forward than front of dovetail.
- Cut new dovetail .731" forward of rear edge
of slide. Depth of dovetail is same as depth of
dovetail of sight.
- Deburr sight and slide & fit sight to slide.
|
 |
|
|
|
Return to TOP |
|
